Home > Error Code > Vita Spa P6 Error Code

Vita Spa P6 Error Code

Contents

GONZO Junior Member Posts: 7 Re: Vita owners….pb code??? Most likely you think there is no power at the spa because the Control Panel/Topside is blank. I did a reset on the top side control and a cold reset (unplug it for 15 minutes) twice and still getting the code. power board looks fairly new, but it is no longer under warranty. http://pdctoday.com/error-code/vita-spa-flo-error-code.php

FL1 = Water flow problem, inhibited or pressure switch malfunction. drops. Hold = Panel sensors have been pressed too many times in a short period of time. Ask mhburris4040 Your Own Question mhburris4040, Home Improvement Enthusiast Category: Pool and Spa Satisfied Customers: 61 Experience: Old School Hardware Guy...20+ years experience working for a large hardware store, not a

Vita Spa Pb Error Code

Not all spa codes are errors, to inform you of trouble, but many codes are used to provide information about system mode, status or equipment operation. Show actual water temp; all seems to be in working order except for the motor will come on and then trip out internally. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Heater disabled but the spa is operational.

Customer: Hello...let me check on that error code..Customer: I think this spa has a Balboa control pack and if so, then the P6 is an error code for the light.Customer: Are I also replaced the filter.The tub starts and runs great heats great.... Logged Trying to be the unbaised voice of reason. Eco Spas Hot Tub Reviews Manuals Attwood Manuals Yamaha Manuals Lowrance Electronics Manuals Raymarine Manuals O'Brien Manuals Show All > Top Musical Instrument Device Types Microphone Manuals Musical Instrument Manuals Electronic Keyboard Manuals DJ Equipment System

I’ll have to check and see if it’s under warranty with a dealer.Dumb Question, but can you tell what the filter would have to do with it? Eco Spa Hot Tub Manual Or so I thought. Is this a Balboa pack? her latest blog Category:Pool and Spa Share this conversation Expert: Poolservice123 replied3 years ago.

Problem is - there's not much consistency among the error codes used by spa pack manufacturers. Eco Spa Reviews Yes No Add Your Answer Please Note: Do not submit personal information as it will be displayed online. help SMF 2.0.12 | SMF © 2016, Simple MachinesSMFAds for Free Forums XHTML RSS WAP2 Home Buying Guide Featured Products Forums Reviews About Contact Copyright ©1998-2016, Whats The Best, Inc. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.

  1. Hello...let me check on that error code..2:07 PMI think this spa has a Balboa control pack and if so, then the P6 is an error code for the light.2:08 PMAre your
  2. Top CGPoolman Swimming Pool Pro Posts: 168 Joined: Sat 28 Apr, 2012 17:52 Location: Orlando FL Eco Spa Hot Tub - Error Code "P6" - Help?
  3. I have 10/30/2016 10/30/2016 billyjr1961 I had a problem with my ground fault breaker and replaced it 10/26/2016 10/26/2016 JACUSTOMER-27j3luit- We just purchased a pre owned Marquis 641R Spa and we
  4. The circuit board says Zettler on it Expert: Poolservice123 replied3 years ago.
  5. The dealer also gave me a topside control to use just incase I still get the Pb code.
  6. drops.
  7. Spa error codes can be somewhat cryptic, but when you have the BIG LIST of CODES, you can immediately define the two or three digit source of trouble.

Eco Spa Hot Tub Manual

If you have a topside control panel then it is more than likely P6 which reports that the topside control is not communicating with the lower circuit board. http://www.spadepot.com/spa-error-codes.htm Noticed your earlier question and thought you should know the reason the wire is clipped is because it is a single speed pump system. Vita Spa Pb Error Code Spa is shut down. Vita Spa Error Codes I also noticed heat damage on both receptacles, one of the pin s on the male ends was black at the bottom, and the female end has obvious heat damage as

Home Help Search Login Register Hot Tub Forum » General » Hot Tub Forum » Vita owners….pb code??? http://pdctoday.com/error-code/winscp-error-code-4-request-code-5.php th3/39 = On startup indicates water temperature less than 39° F. No action is necessary. it's an 10/29/2016 10/29/2016 I had a problem with my ground fault breaker and replaced it 10/26/2016 10/26/2016 JACUSTOMER-27j3luit- We just purchased a pre owned Marquis 641R Spa and we can't Eco Spa Parts

Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature. --- = "Watchdog". Heater is deactivated. If the ozone shorts out it will kill that relay. this content If you need a major part to the spa like the topside control or the circuit board - TSH Tech has the best suggestion of going with a Balboa replacement.

CTI Spa Side Error Codes th1/39 = On startup indicates temperature probe problem. Hot Tub Error Codes Ask an Expert Online. But then every 10 minutes it starts up and runs for 1 minute and then shuts down, and ten minutes later starts up and runs for 1-minute and shuts off …like

but that dang code don't go away.Any ideas???

Since Eco doesn't make parts anymore. It starts hard, unlike when it automatically starts from a cold water start up. Always be sure to check the overlay on the topside control as a maintenance item as well as the silicone. I let it sit up for a few weeks while researching and tried to start it yesterday and it would not turn at all.

Sensor plugged into jack B is not working. Depending on how old your tub is you may be able to find what you need there. dr = Inadequate water detected in heater. have a peek at these guys Simply "click" on the issue below that best suits you for instructions on how to handle.

Submitted: 3 years ago. It did heat up just fine, but now it is not staying warm because the control panel and circuit board are not communicating properly. Does the water heat quicker with the jets off? Sounds like it is trying to "automatically" correct a problem, or re-establish prime.

Not P6 I think. It just cut out and keeps flashing P6 Expert: Poolservice123 replied3 years ago. Spa unusable. BUT, you helped me figure out what part I needed for my hot tub and I really appreciated that:) I will highly recommend your website to anyone needing parts/and or service!!"

The 10/24/2016 10/24/2016 JACUSTOMER-x0uwnnmp- I have a leisure bay spa with a 501s control panel.