Washer F02 Error
You'll need to unseat the filter/pump assembly and then tip it forward to allow the water to clear the floor of the washer chassis. I disconnected this hose and follow where it is connected and viola there is a little canister attachment and it is full of gunk. How do I get to the pump and filter, the front, back top ect. Remove drain & ball from bottom of tub cleaned and reinstalled. http://pdctoday.com/error-code/washer-f06-error.php
Make sure you have hex screwdrivers before you start the process. Close Yes, keep it Undo Close This video is unavailable. Learn more You're viewing YouTube in English (United Kingdom). Here's the water pump for your model(See the handle in the photo below, that's it): Drain Pump 280187 Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance
F02 Error Code Whirlpool Washer
Note: I bench tested the pump and it worked... We have had it for 3 years. Old Turkey03. Up next He3 and He3t DIAGNOSTIC TEST - Duration: 4:18.
It's about how long it takes to drain. I hooked up power to it and it runs but sounds kinda loud. You can change this preference below. F02 Error Code Apc When I opened the plug, stagnant water in the drain line went everywhere.
Working... My husband and I swear to never give Sears ANY more of our money again. Found 5 plastic bb's and a guitar pick.
Thank you for taking the time to write such a detailed comment.
I removed all the debris, re-installed it, and it is working like new again. Kenmore Elite He3 Washer Troubleshooting ReplyWas this helpful?Helpful? This little hose goes from the sensor to a small reservoir behind the tub, it was completely clogged so the sensor never had a good reading about the water level in Any advice?
- Carefully reach up along the inside of the front panel and pull down on the tab that is under the door lock mechanism until it clicks.
- Sign in to make your opinion count.
- What next, take over the world?
- Cancel brucemc777 Rep: 163 3 1 1 Posted: 10/12/2014 Options Permalink History OK, I see many repeats of the same good advice and a few jerks telling those of us who
- Could it be the "water level sensor" Where is that?
- Page 1 of 2 12 Last Jump to page: Results 1 to 10 of 19 Thread: Kenmore Elite HE 3T F02 Error code Thread Tools Show Printable Version Search Thread
Kenmore Elite He3 Washer Error Codes
YesRelatedCategoriesHome and Garden Repair Appliances Clothing WashersAugust 27, 2009GuidesWhirlpool Washer Error CodesElectric Blanket Error CodesMaking an Embroidery Floss and Felt Color Code ChartMaytag Washer Error CodesMore🎃 Halloween Ideas! http://homeguides.sfgate.com/fix-kenmore-washer-f2-code-89793.html Cancel allison bellefontaine Rep: 1 Posted: 12/07/2013 Options Permalink History Ours did the same thing as Darin's machine. F02 Error Code Whirlpool Washer Was this answer helpful? Kenmore Elite He4t Washer Error Code F02 Unscrewed the cover (2 turns) and the expected mess flowed.
Loading... More about the author Autoplay When autoplay is enabled, a suggested video will automatically play next. Clogged or Kinked Drain Hose The drain hose on a Kenmore washer should remain free of obstructions so the water drains from the washtub. I did clear the drain as you instructed, it was full of the backing. F02 Error Code Battery Charger
Finally, the only pipe I did not remove was the small one that goes to the sensor on top of the machine. Plugged it back in, ran the washer and it stopped midway, same code again, washer still isn't draining, the drum doesn't seem to be moving either, but it isn't stuck, I Yes No Voted Undo Score 1 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? http://pdctoday.com/error-code/washer-error-code-f02.php Top #569936 - 10/04/09 11:06 AM Re: Kenmore Elite HE3t washing machine F02/SUDs error [Re: Mark_from_PA] jeff1 Carpal Tunnel Registered: 09/24/03 Posts: 12412 Loc: Ont Canada Hi, Quote: Kenmore HE3t Elite
There is a safety switch near one of the legs that prevents the washer from spinning with the panel off. Kenmore Elite He3 Washer Manual I was surprise about the amount of sh... Sears wanted to charge me $100 to come out and try to sell me a new pump. 11/06/2015 by jlnoll If you can't find anything in the coin trap & the
A little elbow grease and I was able to break the trap free.
Add to Want to watch this again later? Say maybe for $12-15 you could talk to an appliance technician within the hour? Once you have the panel removed, you will see a white plastic unit, that is your pump assembly. Kenmore Elite He3 Washer Parts Good Luck!Ad ReplyWas this helpful?Helpful?
What can it be if it isn't the pump? 04/19/2015 by DW It's a computer, so have you found a way to reset it like you would a car after an I turned the handle on the filter housing and pulled out the filter. Foxboss9 68,260 views 7:36 Whirlpool washing machine drain pump replacement and diagnostic - Duration: 17:45. news I cleaned this small reservoir (don't forget to re-attach the wires to it to prevent them to get in the belt) and my washer work perfectly now.
The tube runs from the pressure switch to the exterior washtub. Nothing. THANK YOU THANK YOU THANK YOU!!! This was both "gag worthy" and unbelievably helpful.
washing machine 438 Questions View all jkiran37 Rep: 73 2 2 Posted: 10/18/2011 Options Permalink History Subscribe Unsubscribe F02 Error Code HE3 Elite Washer The washer displayed the SUD error message, After shutting it down and dismantling the pump I stuck my finger inside to feel the impeller and it was shifting around in a way that didn't seem right. As a preventative measure!! She writes mainly home improvement, health and travel articles for various online publications.
Watch Queue Queue __count__/__total__ Whirlpool Duet F02 error zrda1 SubscribeSubscribedUnsubscribe115115 Loading... So I repeated the procedure. As soon as the clothes are removed, the drain cycle runs successfully.