Home > Error Code > Wd Diagnostic Error Codes

Wd Diagnostic Error Codes

Contents

This may be due to a media error. Replace the drive if the error repeats. This may be an anomaly or a defect with the drive. Return to WDC.com WD Community Contact Us English Product Support My CloudMy BookMy PassportWD Elements & WD TVInternal DrivesWDLabsLegacy & Other Products Downloads WD Software Product Firmware Product Downloads Warranty & have a peek at these guys

Replace the drive if the error repeats. Please contact the system vendor for the above-mentioned information. Ensure that you are using the latest version of diagnostic utility and that your cable is in good working condition. This error can occur on non-Western Digital drives. https://support.wdc.com/knowledgebase/answer.aspx?ID=11711

Dell Hard Drive Error Codes

This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Replace Drive 216 10+ IDNF Errors Identified Data Not Found (IDNF) 10+. Retest and replace the drive if the error repeats.

This may be due to a defect with the drive or a bad connection. Replace Drive 219 Drive Cable Error Failure during cable test. Retest after checking the connections. Re-Test Drive 20 Failed to Delete Partitions A Device I/O Control command during the test has failed.

Ten or more instances of information on data positioning and location could not be found. Wd Error Codes Re-Test Drive 112 IRQ Timeout Interrupt ReQuest Interrupt signal not received. Replace Drive 212 Error while relocating TARE sectors. https://support.wdc.com/KnowledgeBase/answer.aspx?ID=654 Replace Drive 217 2-9 SERVO Errors SERVO 2-9.

Newer Than: Search this thread only Search this forum only Display results as threads More... It also may be due to a defective connection. The snag comes when you leave it off for awhile or have a power surge or loss or it doesn't boot up right somehow....that's where havoc sets in. Self-Monitoring, Analysis, and Reporting Technology (SMART).

Wd Error Codes

SERVO is data on track location. https://hardforum.com/threads/wd-diagnostics-error-code-223.1300005/ It is also possible to see this error on defective Western Digital drives. Dell Hard Drive Error Codes Replace the drive if the error repeats. Western Digital Error Code 0007 Retest after checking the connections.

This may be an anomaly. http://pdctoday.com/error-code/wep-error-codes.php This may be due to a media error. Replace Drive 227 SMART Not Supported Self-Monitoring, Analysis, and Reporting Technology (SMART) Certain older drives do not support SMART. Replace Drive 3 SMART Attribute Read Failure Self-Monitoring, Analysis, and Reporting Technology (SMART) attribute read failure. Seatools

  1. Re-test with appropriate diagnostic utility 222 Drive Failed the Test Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command.
  2. Re-test Drive 134 Busy Timeout Timeout from checking busy bit.
  3. Replace the drive if the repair fails.
  4. The command set to be executed has timed out.
  5. There may be repairable media errors on a platter.

Self-Monitoring, Analysis, and Reporting Technology (SMART). It also may be due to a defective connection. Retest after checking the connections. check my blog This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection.

This may be due to a media error. Check cable & retest. One instance of information on data positioning and location could not be found.

Replace the drive if the error repeats.

Continue to test or exit the test. This error may have internal and external reasons. Retest. There are too many errors detected on this drive to be repaired.

Check your floppy and retest. Drive should be replaced. Check cabling and retest. news Re-test Drive 136 Bad Sector Sector Marked Bad Error.

The drive has detected an unstable condition, possibly an incorrect spin speed. The drive has not responded in the time allotted. The automatic repair feature can attempt a repair if possible. Drive should be replaced.

Replace the drive if the error repeats. Replace the drive if the error repeats. Replace Drive 217 2-9 SERVO Errors SERVO 2-9. Replace the drive if the error repeats.

Return to Top Data Lifeguard Tools 5.22 for DOS Error Codes Note: If the same error code is encountered more than once after re-testing, please Contact Us for additional assistance. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Replace Drive 256 ECC 1 Error Correction Code. Retest after checking the connections.

There were media errors that were within the repair capabilities of diagnostic utility. Drive should be replaced. According to to western digital's site: 223 Errors Repaired Errors found, but have been repaired successfully. No Errors 100 No Errors Found Successful operation.

Re-Test Drive 103 Write Fault Error A Write command during the test has failed to complete. Retest the drive. If ECC occurs, use Data Lifeguard for additional error correction. The drive may not have been accessed properly possibly due to a bad connection.