Home > Error Code > Whirlpool Duet Sport Error Code F 26

Whirlpool Duet Sport Error Code F 26

Contents

F28 Serial Communication Error This error means that the main control and the motor control are not able to communicate. Verify the shipping system including shipping bolts, spacers and cables are removed. 2. I had realized that I forgot to set the spin to low speed since it was an electric blanket, so during the spray, then lock I pushed pause to try to To manually check the function of the Pressure Switch, remove hose from switch and apply air to switch. news

Undo oregpsnow Regus, Why did you point out the machines are made in Mexico? A replacement NTC module (if required) can be purchased at searspartsdirect.com for about $10. Potential Causes • Door lock is broken. • Check door lock switch for foreign objects • Check wire harness connections to the door lock switch and the main control board at Like ApplianceAssistant on Facebook!

Whirlpool Duet F26 Error

Check the motor and do a continuity test. 3. NOTE: Detects by weight. This section of the Duet repair guide shows possible error codes, what they may mean, and what to do next!

  • Do I think it will last 25 years like my old >machine?
  • I cancelled my program, jiggled the door button and and the machine started right away!
  • Open and close the door. 2.
  • Replacement of the control panel is expensive at an average cost of 298 dollars and appears to be the corrective action for other consumers with error code 3E.
  • F30 is a dispenser failure code on the Duet Sport washer.
  • Check the drain hose and make sure it is not plugged or kinked. 2.
  • Check if pressure hose is fi xed correctly. 2.
  • I've ran three loads since and nothing has went wrong.

Whirlpool duet Washing... Check the pressure switch. 8. Coil/Stator Assembly will be defective preventing the drive to operate.You should go for a replacement of that assembly. F26 Error Code Whirlpool Washer The sensor uses a small tube that is attached to the outer tub.

After just over a year of owning it, I started to get the fdl code, followed by the f11 code. Kenmore Washer Error Code F 26 ft. You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. http://www.appliancepartspros.com/diy-story-error-f26-flashing-whirlpool-washer-duet-sport-diy616093.html Easy job.

Check the drive motor for powered rotations. Kenmore Washer F20 Error Code I would suggest that you provide the model # and any other information that you think may help your expert respond with the best possible response. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 4. So far.

Kenmore Washer Error Code F 26

If the washer works, you know it was the door switch. http://mikemerrittmotors.yuku.com/reply/4839/F26-Error-Code-Whirlpool-Duet Refer to the Continuity tests. Whirlpool Duet F26 Error Verify pressure switch operation. 8. Whirlpool Duet Dryer F26 Error Code Unplug washer or disconnect power. 3.

Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). 5. http://pdctoday.com/error-code/whirlpool-duet-sport-error-code-f-27.php SamuraiRepairman 143,734 views 12:49 Kenmore HE2 Plus 110.47531700 F21 - F01 - F20 - Duration: 1:05. Check drive motor tachometer resistance. Loading... Whirlpool Duet Sport F26

Replace User Interface if drum is rotating. 4. Replace Central Control Unit if drum is not moving F71 USER INTERFACE HEARTBEAT FAILURE If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the User Interface Turn off hot and cold water faucets and unplug the unit before servicing. 1. More about the author Consumer Reports' reliability surveys are the best we have, and Whirlpool's 10% front-loader repair rate is low compared to other manufacturers.

Verify CCU operation by running a Diagnostic Test or any cycle. Kenmore He2 Plus Error Code F20 This problem has forced me to use a local laundry mat to wash my clothes. Check the water temperature sensor and connection to it. 3.

Oct 12, 2008 | Whirlpool Duet GHW9150P Front Load Washer Not finding what you are looking for?

This should clear the unit of the excess detergent. 1. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. F03 HEATER SC TO GROUND The Heater has a internal short circuit. Kenmore Washer Code F21 Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the

rL LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE If at the start of the CLEANING WASHER cycle a load is detected inside the drum. Plug in washer or reconnect power. 4. Double check that the spring band is in it's proper groove with the rubber gasket properly seated. click site Published on Aug 6, 2014a tutorial video on how to fix a Kenmore washer that has a F20/21 or F26 code.