Whirlpool Duet Sport Error Code F-27
If resistance is 0 Ω or infi nite value, replace NTC. 4. OR Press STOP/CANCEL to clear the display and completely cancel the cycle. Exchange steamer electronic board if valve is OK. Unplug washer or disconnect power.3. news
I think the door lock system might be the next part to look at?? Check connection to water heater. 3. Check the drain hose and make sure it is not plugged or kinked. 2. The issue became worse until it was very difficult to get a full cycle completed. why not find out more
F27 Error Code Kenmore
If there is an error reading this data, it will cause this error. Check Pressure Switch for correct working with a DVM/VOM. 3. Check the MCU by looking for operations of the drive motor. 7. Until we 11/1/2016 11/1/2016 centralappliance1 When putting my stove on clean, it comes up with F9 error, 11/1/2016 11/1/2016 woody463 X Ask an Appliance Technician Get a Professional Answer. 100% Satisfaction
- Ask Bryan Your Own Question Bryan, Home Appliance Technician Category: Appliance Satisfied Customers: 12156 Experience: 15 yrs.
- F29 DOOR UNLOCK ERROR If the door unlock has failed 6 times.
- Check if the airtrap is not blocked. 3.
- The failure will be reset after running the Diagnostic Test Program.
- Replace also the CCU.
- there may be something in the pump impeller or the hose going out from it, if you can get me the full model # XXXXX'll send you a link to the
- Check/clean drain pump filter of foreign objects. 5.
- Make sure you drain the water from the drain lines, pump and hoses PRIOR to removing the cover.
- Verify inlet valve operation.
- This should clear the unit of the excess detergent.
Hope this helps, good luck. Check the drain pump filter for foreign objects. Look for condensation or contamination on probe receptacle. check that all the connections to the main control are fully connected.
Sd SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4 Unplug washer or disconnect power. 2. Sd SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4 http://www.justanswer.com/appliance/3s27a-f27-error-whirlpool-duet-washer.html F03 HEATER SC TO GROUND The Heater has a internal short circuit.
paul sti 15,051 views 1:59 Whirlpool Fault Codes - Duration: 3:39. Check the drain hose and make sure it is not plugged or kinked. 2. Check resistance of heating element, if present on this model. (abnormal = infinity) 4. Rating is available when the video has been rented.
Whirlpool 6th Sense Washing Machine Error Codes
Check that the tab on the washer's door that inserts into the door lock is not broken, that it's properly aligned with the door lock hole, and that there is nothing
Remove the washer to and do a Duet Washer Quick Diagnostic Test step C02 should move the dispenser linkage so you can see what's the hang-up. F27 Error Code Kenmore Check the water temperature sensor and connection to it. Whirlpool Front Load Washer Error Codes F5 - E1 Self clean latch will not lock F5 - E2 Latch during CLEAN error F5 - E5 Self clean temperature not reached within 45 minutes.
If after 30 seconds not minimum 0.1l of water entered or maximum fi ll time of 13 minutes is exceeded, the valves will be turned off and the error code will navigate to this website Check the inlet valve for proper shut off. 7. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. Check the electrical connections at the pump and make sure the pump is running. 4. Whirlpool Washer
NOTES: After 4 minutes the “Sd” error will be displayed, then 4 minutes later the “F/21” error code will be displayed. Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU).4. Unplug washer or disconnect power. 2. More about the author Unplug washer or disconnect power. 3.
See Manually Unlocking The Door Lock System. Check wire harness connections to the User Interface and the Central Control Unit. 3. Jen Russo 1,622 views 3:20 Whirlpool Duet Sport ht - F 21 error, will not drain. - Duration: 2:54.
Cabrio Top ...
Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). Ultimate Handyman 618,857 views 4:02 Whirlpool Duet clogged washer - won't drain F21 error - Duration: 3:20. Door lock mechanism is broken. Mariela Gonzalez-Aroche 118,085 views 5:40 Washer Won't Drain? – Duet/HE3 Front-Load Washer Drain Pump Replacement (part #280187) - Duration: 2:21.
Plug in washer or reconnect power. 6. Unplug washer or disconnect power. 3. See Details More Products Whirlpool WTW5000DW 4.3 cu. click site Press PAUSE/CANCEL two times to clear the display. 1.
Unplug washer or disconnect power. 3. Exchange steamer electronic board if valve is OK. Replace MCU board. Perform test program.
The problem could be in ether the main control or the motor control boards This problem is usually a good one to have a professional repair person diagnose, because both possible Check the pressure switch. 8. Sign in Loading... The drive motor must be hooked up properly or a "CE" error will occur. • Drive motor thermal protector has opened. • Motor controller is not powered or fuse has opened.
B. F2 will appear. To manually check the function of the Pressure Switch, remove hose from switch and apply air to switch. Potential Causes • Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the MCU
F11 MOTOR CONTROL UNIT ERROR The Motor Control Unit has internal failure; repeating under or over voltage, or over current conditions. Check for drain pump failure.6.