Home > Error Code > Whirlpool Duet Washer Error Codes F 27

Whirlpool Duet Washer Error Codes F 27

Contents

Siguiente Whirlpool washing machine drain pump replacement and diagnostic - Duración: 17:45. Check the MCU by looking for operations of the drive motor. 7. When I go to start the cycle door clicks drum rotates and then water leaks 1 answer Related Questions'>I have whirlpool Duet sport and get a error code F-33, help? 1 If the error code reappears, proceed to step 2. 2. news

F31 MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will communicate this failure to the Central Control Unit (CCU), Check the water temperature sensor and connection to it. 3. Plug in washer or reconnect power. 4. Replace motor controller.

Whirlpool Duet F27 Error Code

After disconnecting power to the unit, try scraping this coating off the pins. • Check the resistance values between the serial communications pins with the connectors in place. The failure will reset after running the Diagnostic Test Program. 1. If failure occurs during high-speed spin the door unlocks after 3 minutes. 1.

F9 Oven door lock failure Check wiring to door lock switch (the wire harness may be connected wrong). Unplug washer or disconnect power. 3. Potential Causes • A power glitch may cause this error. Whirlpool Washer Press PAUSE/CANCEL twice to clear the display.

NOTES: After 4 minutes the “Sd” error will be displayed, then 4 minutes later the “F/21” error code will be displayed. F27 Error Code Kenmore F06 Drive motor tachometer error The control is unable to properly detect motor speed and the machine will shut down. F30 DISPENSER SYSTEM ERROR When the dispenser motor cannot be driven to its proper position. 1. Verify CCU operation by running a Diagnostic Test or any cycle.

Verify inlet valve operation. The next most likely cause is that the washer's water valves are not opening for some reason. (Check the valves with a Duet Quick Diagnostic Test) F21 Long Drain Error This I fixed my Duet thanks to you. F99 NOT SUPPORTED User selected on the UI the unsuppor ted Cycle on the CCU.

  • F06 STEAMER DEFECT The Steamer temperature has not reached the correct value.
  • NOTE: The door switch/lock unit can be manually unlocked.
  • Sud SUDS LOCK (Overdose of detergent detected during the wash cycle) The motor control unit senses a suds lock condition by analyzing the current draw on the drive motor.

F27 Error Code Kenmore

You may have a loose or dirty connection somewhere. MAIN RELAYS ERROR One of the main relays is not working properly. Whirlpool Duet F27 Error Code WHIRLPOOL FAULT CODES Whirlpool Duet Front Loading Gas and Electric Dryer Fault Codes Failure Code Fault Code Description Solution PF Power failure "PF" flashes to indicate that a power failure occurred Whirlpool Front Load Washer Error Codes Check the motor and do a continuity test. 3.

They use the status lights on the touchpad/LED. navigate to this website Thanks for the logical explanation & valuable insight. A power glitch may cause this error. Verify wire harness connections to inlet valves, pressure switch, drain pump and Central Control Unit (CCU). 5. Whirlpool 6th Sense Washing Machine Error Codes

Unplug your machine anytime you work on it. Press STOP/CANCEL to clear the display. Overloading the unit may cause this problem. More about the author F28 SERIAL COMMUNICATION ERROR The communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. 1.

Check for continuity of the User Interface harness. 2. Check doorswitch system. (See checklist of F26 and F29). Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 4.

F22 DOOR LOCK ERROR After 6 failed attempts to lock the door.

A double oven will have two of each switch and one common wire. 1. Failure Code LED Status Duet Sport LED Status Duet Sport HT F01 Add a Garment Add a Garment F11 Add a Garment, Wash, Spin Add a Garment, Soak/Prewash, Rinse F20 Rinse, With an overfill condition, the beeper repeats a warning every 10 seconds with no time out. Replace User Interface if drum is rotating. 4.

Verify CCU operation by running a Diagnostic Test or any cycle. Cola de reproducciónColaCola de reproducciónCola Eliminar todoDesconectar Cargando... F33 PUMP DRIVE SYSTEM ERROR When the connection between pump and the Central Control Unit (CCU) is lost. 1. http://pdctoday.com/error-code/whirlpool-duet-washer-error-codes-f70.php codes.

But these serial communications error codes all have one big thing in common: They are almost NEVER caused by a bad circuit board! Plug in washer or reconnect power. 6. normally this is due to too much soap or non HE detergent being used. Check the water temperature sensor and connection to it.

This may signify problems with the drive motor, thermal protector or motor controller.