Home > Error Code > Whirlpool F 15 Error Code

Whirlpool F 15 Error Code

Contents

F07 Motor control unit error The Central Control Unit has detected a short in the motor control unit. Replace Central Control Unit if drum is not moving. Check Pressure Switch harness for continuity. 2. rL LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE If at the start of the CLEANING WASHER cycle a load is detected inside the drum. http://pdctoday.com/error-code/whirlpool-f11-error-code.php

Sign in to add this video to a playlist. Check the drive motor for powered rotations. Check/clean drain pump filter of foreign objects. 5. If no damage to wires and all connectors okay, proceed to step C.

Whirlpool Washer Error Codes F21

Check the pressure switch. 8. It should be approx. 115 Ω. 4. Unplug washer or disconnect power. 3.

Check the pressure switch. 8. F26 DOOR SWITCH ERROR If the door has not been opened for 3 consecutive cycles or the door switch is open while the door is locked for more than 5 seconds. Replace heater. Whirlpool Top Load Washing Machine Error Codes Make sure that both valves at the water source(s) are turned on all the way. 2.

Repeat steps A and B for door switch. 3. Whirlpool Top Load Washer Error Codes After disconnecting power to the unit, try scraping this coating off the pins. • Check the resistance values between the serial communications pins with the connectors in place. If Pause/Cancel does not work: Unplug washer or Question about Whirlpool duet Washing Machines 1 Answer 07f error code... In winter, check the fill lines for freezing.

Door Lock Mechanism broken or removed from the Door Check Door Lock/Switch Assembly Check the wire harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) Door Lock/Switch Assembly Whirlpool Duet Reset codes. Check connections of the CCU board within the housing. See the repair guide to fix it yourself Water inlet valve assembly F/02 Takes a long time to drain Remove excess suds; the washer can't drain excessively sudsy water.

  1. Unplug washer or disconnect power. 3.
  2. Check the drive system for any worn or failed components. 5.
  3. Perform test program.
  4. F7-E1 - Common Switch Wire Is Defective - This error occurs when common wire to latch switch and door switch is shorted.

Whirlpool Top Load Washer Error Codes

OR Press STOP/CANCEL to clear the display and completely cancel the cycle. http://www.appliancehelponline.com/whirlpool.html This may signify problems with the drive motor, thermal protector or motor controller. Whirlpool Washer Error Codes F21 The doorswitch may cause an interference for the powersupply of the MCU. Whirlpool Duet Dryer Error Codes Press STOP/CANCEL to clear the display.

Click here for more details. navigate to this website Close the lid and press START to continue with the cycle. google + facebook twitter Liked Your Experience? If a potential suds lock is detected, the control tries up to 3 times to clean out the unit with a mini-cycle. "SL" is displayed if suds are detected but the Whirlpool Washing Machine Error Codes E1

F06 Drive motor tachometer error The control is unable to properly detect motor speed and the machine will shut down. Check the drain system for a siphon problem. Your Duet washer was not able to unlock after 6 tries. More about the author F31 MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will communicate this failure to the Central Control Unit (CCU),

Proceed by checking the drain hoses for proper connection and kinks. Whirlpool Dryer Error Codes Gently pull the tab down about 1/4 inch or until a click is heard. 6. If door latched: Disconnect power from unit.

Press STOP/CANCEL to clear the display.

Refrigerator 25 Cu.

F21 LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off. It can also indicate a bad pump, an extra heavy load, excessive detergent, or excessive suds. Press CANCEL and observe for 1 minute to ensure operation is correct. 6. Whirlpool Washer Error Codes A10 Refer to the Water Temperature Sensor section.

Door not opened during 3 consecutive cycles. 1. PUMP DRIVE ERROR The pump driver fails to activate. Unplug washer or disconnect power. 2. click site CT Sat7:00 a.m. - 9:00 p.m.CT Sun7:30 a.m. - 9:00 p.m.CT About Us Contact Us Top Parts Affiliate Program Parts Store Locations Sears Commercial Parts All Brands All Categories Appliance Parts

If too much detergent was used: Run the unit through a RINSE/SPIN cycle. If a failure occurs during high-speed spin, the door unlocks after 3 minutes. 1. Loading...Oops :Please try again. F09 - Overflow Condition (Pressure Switch Closed Too Long) - Check to make sure drain hose is not plugged or kinked and unplug the unit and disconnect power.

Check the motor and do a continuity test. 3. Kansas City, KS "Robin went above and beyond the call to assist me and I was very impressed." Val T. Replace control. Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit.

The drive motor must be hooked up properly or a "CE" error will occur. • Drive motor thermal protector has opened. • Motor controller is not powered or fuse has opened. F2 - E0 Shorted keypad (also called touch pad) 1. Check door switch/lock unit for foreign objects. 2. codes.

Average current trip occurs if there is a 2 second average of current draw greater than 5.55 Amps at the motor windings. Door Lock Mechanism broken.