Home > Error Code > Wirlpool Microwave Error Codes

Wirlpool Microwave Error Codes

Contents

If too much detergent was used: Run the unit through a RINSE/SPIN cycle. Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 4. Note: Double ovens will have two of each switch and one common wire. 2 Digit Failure Codes F0 - Control Board Failure - Replace control board (clock). Replace the Motor Control Unit. weblink

Press 'Stop/Cancel' to clear display. Unplug washer or disconnect power. 2. F20 NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED. The consumer or reader is individually responsible for his or her use of the information supplied and uses this information at their own risk.

Whirlpool Oven Error Codes

Ensure you have read our Small Print page before using information supplied via this website. ©2003 We use Cookies. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. Check/clean drain pump filter of foreign objects. 5. Replace door switch.

NOTE: To find correct Ohm reading refer to the Water Temperature Sensor section. 1. You may have to register before you can post: click the register link above to proceed. F11 Serial communication error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. Whirlpool Top Load Washing Machine Error Codes If a failure occurs during high-speed spin, the door unlocks after 3 minutes. 1.

Hope the bug stays away. Whirlpool Washing Machine Error Codes E1 Turn off hot and cold water faucets and unplug the unit before servicing. 1. Flashing display time Open lid If the lid opens while the unit is in running mode, time remaining will flash in the display. More Help Why do European power outlets all have a switch?

Plug in washer or reconnect power. 6. Whirlpool Accubake Oven Error Codes Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. F06 Drive motor tachometer error The control is unable to properly detect motor speed and the machine will shut down. Proceed by checking the drain hoses for proper connection and kinks.

Whirlpool Washing Machine Error Codes E1

F2 - E1 Keypad cable unplugged F2 - E5 Cancel key drive line open F2 - E6 Cancel key drive line open F3 - E0 Oven temperature sensor (RTD) opened (upper Potential Causes • Check mechanical linkage from dispenser motor to the top of the dispenser. • Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU) • Check Whirlpool Oven Error Codes Check MCU by looking for operations of the drive motor and check drive motor for powered rotations. Whirlpool Range Error Code F9e0 All rights reserved.

CE Communications error If there is any breakdown in communication between the machine controller and the motor controller, "CE" flashes and the unit beeps once. http://pdctoday.com/error-code/wii-error-codes-101.php Roughly How many kilowatt hours, is used when a person ... 1) Uses an average size stove's burner for one hour? FdL - Door Lock Error - It is possible the door lock mechanism is broken or removed, or the door switch/lock unit has failed. It was easy and now our mic works again! Whirlpool Top Load Washer Error Codes

  1. Disconnect power and unplug the unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU).
  2. Thankx for the update...that should help others jeff.
  3. Note: The door lock/switch assembly can be manually unlocked.
  4. F61 STEAMER COMMUNICATION FAILURE An incorrect or corrupted communication between Central Control Unit (CCU) and steamer electronic board is recognized.

I had broken one of the locking tabs before when I had taken it apart and broke the other one this time while making the Kean repair. Advertisements Important Attempting repairs can be dangerous. Check the motor and do a continuity test. 3. check over here Check the operation of all interlock switches. 3.

The failure will be reset after running the Diagnostic Test Program. 1. Whirlpool Range F9 Error Code Check the wire harness connections to the door switch/lock unit and Central Control Unit (CCU). Some models incorporate keypad in to control board as one unit.

Replace failed component.

The codes are programmed in home appliance controls, each of them refer to a specific issue (issues). Patience and about 20 minutes is all it should take to fix it. NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed. Whirlpool Oven Error Codes E2 F3 Press 'Stop/Cancel' to clear display.

Check for continuity of the User Interface harness. 2. Reverse the order of assembly from above.15. 13. Fila de exibição Fila __count__ / __total__ Possible source of Microwave F7 error code - Whirlpool GE HBT Inscrever-seInscritoCancelar inscrição4.3794 mil Carregando... this content If probe is plugged in and "ProbE" is on display, check probe for continuity with ohm meter.

Tom « Last Edit: May 21, 2013, 07:46:59 PM by tagarman » Logged scrapiron Technician Member Since: Nov 2011 Posts: 241 Country: Service Tech Since 1974 Re: Maytag Microwave Oven Locks Exchange the complete valve block if the steamer valve has not a resistance of approx. 812 Ω between both contacts. 6. Verify the shipping system including shipping bolts, spacers and cables are removed. 2. F5 - E6 Door is open, but latch is locked F5 - E7 Self clean latch will not unlock F6 - E0 Return line not connected If switch pulse return line

Check for proper installation, verify the unit is not located near a source of heat and has proper ventilation. 2. Replace switch if defective. 4. Press START to continue the cycle from the moment that power was lost. I unplugged the microwave, and plugged into a different outlet.

In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Also check the motor and wire harness. The error hasnt occurred since. To repair, I folded up some paper behind the ribbon to make the fit tight and secured it with some tape.

Try unplugging unit for two minutes to see if that fixes error. You can test this feature by holding in one of the keypads for over 60 seconds - F3 will display. If door is latched, disconnect power from unit and check wires and connections. The pump is cycled in drain mode for 30 seconds on, 30 seconds off until the overfill switch resets or power is discontinued to the unit.

F28 SERIAL COMMUNICATION ERROR The communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. 1. NOTE: The door switch/lock unit can be manually unlocked. Check that the control cable to the 1100 watt inverter is properly connected to plug P2 on the display PCB & Adjust or Reconnect 7. Oven worked for a while but eventually threw up the same error code.

Perform test program. Check/clean drain pump filter of foreign objects. 5. My microwave is screwed up, I tried unplugging it, and hitting all the buttons (In case it was screwed up).