Winsock 10004 Error
WSAEMSGSIZE (10040) Message too long A message sent on a socket was larger than the internal message buffer or some other network limit. Developer suggestions: Don't call bind() in a client application. WinSock description: Same as Berkeley. The following list describes the possible error codes returned by the WSAGetLastError function. navigate here
Recv and Recvfrom: If the datagram you read is larger than the buffer you supplied, then Winsock truncates the datagram (i.e. WSA_E_NO_MORE 10110 No more results. This error occurs if you specifically reference a protocol that isn't part of the address family you also reference. WSAETIMEDOUT 10060 Connection timed out. https://msdn.microsoft.com/en-us/library/windows/desktop/ms740668(v=vs.85).aspx
Socket Error 10054
However, there's little distinction between WSAEALREADY and WSAEINVAL since a WinSock DLL cannot tell the difference between an asynchronous operation that has been cancelled and one that was never valid. Is the router up and running (check by pinging it, and then ping an address on the other side of it)? Note that this error is returned by the operating system, so the error number may change in future releases of Windows. Unlike Berkeley, however, WinSock v1.1 doesn't ascribe this error to any functions.
The ICMP message means that the router can't forward the IP datagram, possibly because it didn't get a response to the ARP request (which might mean the destination host is down).WSAENOTEMPTY Seasonal Challenge (Contributions from TeXing Dead Welcome) Why didn’t Japan attack the West Coast of the United States during World War II? PC Review Home Newsgroups > Microsoft DotNet > Microsoft Dot NET Framework > Home Home Quick Links Search Forums Recent Posts Forums Forums Quick Links Search Forums Recent Posts Articles Articles Socket Error 10054 Connection Reset By Peer See also: WSAECONNRESET, WSAENETRESET, WSAETIMEDOUT WSAECONNREFUSED (10061) Connection refused.
You'll be able to ask any tech support questions, or chat with the community and help others. Socket Error 10053 An operation on a socket could not be performed because the system lacked sufficient buffer space or because a queue was full. Berkeley description: The quota system ran out of table entries. http://stackoverflow.com/questions/26307738/best-way-to-handle-a-winsock-10004-error Typically, though, WinSock generates this error when it receives a "host unreachable" ICMP message from a router.
The call has been canceled. Socket Error 11004 NFS is 'network-related' in the strictest sense, but the NFS protocol is an application protocol (that is, a 'high-level' protocol). WSAEISCONN (10056) Socket is already connected A connect request was made on an already connected socket; or, a sendto or sendmsg() request on a connected socket specified a destination when already Format error: Name server was unable to interpret the query.
- This is usually caused by one or more of the function pointers being NULL.
- Detailed descriptions: connect(): the operation is underway, but as yet incomplete.
- An unfinished installation, an unfinished file erasure, bad deletion of applications or equipment.
- Winsock only allows a single blocking operation to be outstanding per task (or thread), and if you make any other function call (whether or not it references that or any other
- This would occur if WinSock aborts an established connection after data retransmission fails (receiver never acknowledges data sent on a datastream socket).
- The requested address is not valid in its context.
- Typically their descriptions are similar.
- The application may be accessing a socket that the current active task does not own (that is, trying to share a socket between tasks), or WSACleanup has been called too many
- It may also indicate you are not closing the applications properly.
- Berkeley description: A socket operation was attempted to an unreachable network.
Socket Error 10053
Berkeley description: A write to an ordinary file, the creation of a directory or symbolic link, or the creation of a directory entry failed because the user's quota of disk blocks https://www.postgresql.org/message-id/[email protected] Detailed description: select(): fails with WSAENOTSOCK if any socket in an fd_set is an invalid socket handle. Socket Error 10054 Detailed description: There's at least one WinSock implementation that will occasionally fail a function and report this as the error value, even though the function succeeded. Socket Error 10049 A retry at some time later may be successful.
Among other things, that is exactly what we've done here. check over here I added the epicsExit(0) call to the IOC's that are in areaDetector, and then began receiving errors with these on exit also. This error occurs if the sin_addr is INADDR_ANY (i.e. The missing functions are getprotobyname(), getprotobynumber(), getservbyname(), and getservbyport(). Socket Error Codes Linux
WSAESTALE 10070 Stale file handle reference. WinSock description: a quick comparison to the Berkeley counterpart, and a long description of WinSock error. WSA_QOS_REQUEST_CONFIRMED 11009 QoS request confirmed. his comment is here WSA_QOS_EFLOWDESC 11026 Invalid QoS flow descriptor.
WSAEAFNOSUPPORT (10047) Address family not supported by protocol family. Winsock Error 10061 If the signal handler performs a normal return, the interrupted function call will seem to have returned the error condition. Winsock Error 10004, Error -107 error codes are often brought on in one way or another by faulty files_new in the Microsoft Windows OS.
WinSock functions: WSACancelAsyncRequest() Additional functions: Berkeley sockets connect() returns this error on subsequent calls, after an initial call on a non-blocking socket.
WinSock description: Same as Berkeley. "You can't make a silk purse from a sow's ear." Detailed descriptions: accept(), listen(): socket is not of type that supports connection-oriented service. It also occurs with functions that take a socket handle and a sockaddr structure as input parameters. Developer suggestions: If you have a network analyzer available, you can quickly check if the destination port number and host address are what you expect. Socket Error 10061 Connection Refused If you have more than one server configured, the hostname query fails only after the WinSock DLL has queried all servers.
See WSASYSNOTREADY for details. A couple functions that the v1.1 specification missed are WSASetLastError() and WSAUnhookBlockingHook(). This unique Winsock Error 10004, Error -107 error code features a numeric value and a practical description. weblink WSA_QOS_GENERIC_ERROR 11015 QoS generic error.
Some of the types of things you will find under some errors are: Microsoft C description: the first few WinSock errors are carry-overs from the standard 'C' runtime library. A server has attempted to handle an NFS request by generating a request to another NFS server, which is not allowed. A name component or a name was too long. Developer suggestions: Always check the return value from a memory allocation to be sure it succeeded.
after the first failed with WSAEWOULDBLOCK). Which is bad news for you, because I don't really know that much. WinSock description: No equivalent. An invalid shaping rate object was found in the QoS provider-specific buffer.
The explanation is simple and obvious: in order to connect to or send to a destination address, you need to provide the destination address. Fresh install time.! :) Thanks again. You can avoid making the mistake of trying to send on a socket after you've initiated a close, by keeping track of the socket state in your application (and checking it The service provider procedure call table is invalid.
Try reconnecting at a later time.WSAECONNABORTED (10053) Software caused connection abort A connection abort was caused internal to your host machine. Do you have a router configured? Berkeley description: Too many open files. WSA_QOS_ESHAPERATEOBJ 11030 Invalid QoS shaping rate object.
Microsoft C description: Bad file number. An unknown or conflicting QoS style was encountered. If you don't have the proper subnet mask, your network system may treat a local address as a remote address (so it forwards addresses on the local subnet to the router,