Home > Whirlpool Duet > Whirlpool F H Error

Whirlpool F H Error

Contents

This may be due to hard water conditions or sediments in the water. I don't know what the resistance is supposed to read, maybe some of the other guy's out here, that like to piggy back on me here, have more time to find Find out more » Total: $31.76 Add to Cart Install Help Watch this helpful video to determine how to install your part. Up next Whirlpool, Kenmore, KitchenAid Dishwasher Repair - Quits Running Mid Cycle - Duration: 6:10. news

The shiny new flow meter was connected to the water line and to its wiring harness. Sign in to make your opinion count. Using non-HE detergent, or more than the manufacturer's recommended amount of detergent, can cause excessive suds.The excess suds can prevent the washer from detecting theincoming water. should it fill past baffle fins in drum?.

What Does Fh Mean On A Whirlpool Washer

Turn off the water and remove inlet hoses from the inlet valves in the back of the washer. This code can also display if the machine is filling with water, the flow meter measures 10.5 gallons of water into the machine, but the water level pressure switch does not i ..." User Name Remember Me?

  • If this happens the water inlet valve or the water level pressure switch may be defective.
  • This video demonstrates how to test a water inlet valve on a washing...
  • The washer will not properly operate with only one incoming source of water.
  • Inside the inletvalves are screens.Remove any accumulated film or particles from the screens.
  • I checked the hose going to the pressure switch because I read someplace that that could be a problem and its in good shape.

I checked the hose going to the pressure switch because I read someplace that that could be a problem and its in good shape. Register Help Remember Me? Being a fairly basic component, it seems unlikely these flow meter would ever actually fail, but the fact is, given different water conditions the wheel inside can start to rotate slower. Whirlpool Duet Pressure Switch Finally, if all other things check out, the problem might be with the central control unit circuit board (CCU) or the wiring to any of these components.

Shop Parts Repair Help SEARCH Return to previous page Whirlpool Washing Machine Displaying Fault Code F/H GHW9100LW1 FH No water detected entering machine or Pressure switch trip not detected. Whirlpool Duet Flow Meter In this case, check the water supply to be sure you have good pressure for both hot and cold water. how do you check flow meter to see if it is ok? DPLrepara 14,086 views 1:58 Kenmore Elite HE3 Washer Error FH FIXED - Duration: 6:32.

It had a comb, a key, several paper clips, a pair of (disintegrated) reading glasses, several bolts and screws, and 65 cents in change, among the identifiable stuff. Whirlpool Duet Diagnostic Mode This error code will be displayed if the machine is trying to fill with water but the flow meter doesn’t sense any flow for 30 seconds. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! Top 5 Reasons Top-Load Washer Won’t Start?

Whirlpool Duet Flow Meter

I use that term because few answers usually come form error messages. http://www.applianceblog.com/mainforums/threads/16763-Whirlpool-Duet-Washer-Getting-FH-code Over 650 Posts « Maytag Refrigerator Freezing Vegetables Frigidaire Freezer not Cooling » Whirlpool Washer ‘FH' Error Published November 1, 2009 | By Brian Dawson Model #GHW9100LW1, this front load Duet What Does Fh Mean On A Whirlpool Washer Then the HF code again. Ghw9150p Errorcodes The time now is 08:39 PM.

Parts Water Inlet Valve for your Whirlpool Washing Machine RepairClinic Item #906483 Washing machine water inlet valve. navigate to this website All times are GMT -5. Looking for a Specific Part? Unscrew the pump cover, and see if there is not a bunch of stuff in the pump, causing it to slow drain. Fh Error Code Maytag Washer

The repair was complete and the customer could again use the washer without starting it a second time. NOTE: Both hot and cold water must be connected to the washer supply and turned on. Transcript The interactive transcript could not be loaded. More about the author On this washer a quick look at the tech sheet provided this tidbit of information.

Loading... Whirlpool Duet Washer Codes This is a safety measure to prevent flooding. Powered by vBulletin Version 3.6.4Copyright ©2000 - 2016, Jelsoft Enterprises Ltd.

During successive loads, the problem would occasionally reappear, but each time starting the cycle over did the trick.

Whenever an error message of any kind appears, it is best to use this information the machine is providing and consult the technical documentation for suggestions. These hoses have a valve insidethat will close if the water pressure ishigher thantwo gallons per minute; this willshut off the water to the washer.If one of these hoses becomes loose, Arethe water inlet hoses kinked? Whirlpool Duet Washer Parts Sign in Transcript Statistics 31,617 views 27 Like this video?

So it doesn't need to completely fail to present itself as a problem. Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the Add Thread to del.icio.us Bookmark in Technorati Tweet this thread 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Skip to main click site In this case, check the water supply to be sure you have good pressure for both hot and cold water.

If a cold water wash is selected, the washer is designed to add hot water to keep the temperature optimal for cold wash performance (75°F +/-10°).If you want to save energy Presented by - All Tech Appliance Service, your Portland Oregon appliance repair company. The time now is 06:39 PM. All rights reserved.

Since each error came very early in the wash cycle I decided to make some checks of the flow meter. Check the household faucets to see if the hot and cold water faucetsare turned on.Make sure toopenboth faucets completely for proper fill. NOTE: This part is often misdiagnosed and requires electrical testing with a volt/ohm meter to determine if it is defective. $263.10 Quantity: In Stock › Order now and this item will Sign in 21 Loading...

Then the HF code again. what is test for flow meter? Finally, if all other things check out, the problem might be with the central control unit circuit board (CCU) or the wiring to any of these components. Tom #9 (permalink) 07-21-2009, 01:26 PM ericsaraw Junior Member Join Date: Jul 2009 Posts: 2 Quote: Originally Posted by misterfixall there is no problem with pump.

The manufacturer has assigned this error or fault code to indicate that there is a problem with the amount of water entering the machine. All rights reserved. LinkBack Thread Tools Search this Thread Display Modes #1 (permalink) 01-05-2009, 11:49 AM misterfixall Senior Expert APP Volunteer Join Date: Nov 2007 Location: brampton ontario outside of toronto Each message has a purpose and may point in a particular direction, but they are rarely spot on when it comes to locating failures.

Remembering of coarse that the codes appear based on what the machine was doing at the time and not necessarily what went wrong. Visit us online at www.AllTechAppliance.com Leave a Reply Cancel reply You must be logged in to post a comment. Top 5 Reasons Top-Load Washer Is Making Loud Noise?